Want to have this awesome stairs lighting in your home or showroom?

A system which support maximum 32 steps, 300Watts of Power. 

You need to install the motion sensor at both downstairs and upstairs and connect them to the control system. When the downstairs sensor senses any movement, the control system will light up each LED strips of steps from the bottom-up. On the contrary, when the upstairs sensor sense any movement, the control system will light up each LED strips on the steps from top-down. 

• A Stairs step LED strip control system with two motion sensors.
  
• A transformer with enough capacity to power all LED strips and controller.
  
• A certain amount of LED channels ( LED strips inside a particular shape of aluminum profile with a soft light PC cover)
  
• Cables with double insulated 2-wire to power LED channels for each step.
  
• Extended cords (double insulated 3-wire, or CAT5 cable) to connect motion sensor when needed.
  
• A trustable supplier for pre-sales and after-sales services.
  

1. make sure your stairs can install LED channel for each steps.
   
2. Confirm the numbers and lengths of each LED channel, add up and see the total power consumption less than 300Watts.
   
3. Confirm you have installed double insulated 2-wire cables for each steps
   
4. Confirm you have installed double insulated 3-wire, or CAT5 cable) to connect motion sensor.
   

1. Make sure to connect DC12-24V power into the controller. And for each LED strip output socket, please use at least 0.5mm^2 cables to the LED strip, and try not to use long cables.
   
2. Make sure you know how to calculate the correct power of the Power supplies. You need to consider strips, controllers, cable losts, and allowance. If no, please contact with us.
   
3. Try to use DC24V LED strip instead of DC12V, to lower the cable running current, and lower voltage drops.
   
4. Better to tape LED strip into aluminum profile for supporting. And we could provide customized lengths service.
   
5. Each step needs an independent cables and connected into controller in proper sequences. Cannot use common cable for two different steps.
   
6. Make sure not to install the signal wires of sensors and strips with normal electricity cables. And use CAT5 cables for signals.
   
7. Setting steps in controller: Long press botton to set, and adding each step by each press, and long press to finish. And set speed from 1-4 to fit your walking speed. Please refer to videos.
   
8. LED strip flickring, and not running correctly, please check the input voltage of the strips, power supply wattages, and signal interference.
   
9. For sensor sensitive problems, please try to find a best position when you install the sensors. Sensors working in this way: not sense anything, voltage of VCC and GND is 12/24VDC, and voltage of DI and GND is 0 VDC. And if it senses something, the voltage of DI and GND will change into 3.3VDC and maintain for around 3 seconds.
   

A system which support most 500ics (approximate 8 meters) LED running strips. 

You need to install the motion sensor at both downstairs and upstairs and connect them to the control system. When the downstairs sensor senses any movement, the control system will light up the running LED strip installed on the sideway of stairs. On the contrary, when the upstairs sensor senses any movement, the control system will light up the running LED strip from top-down. All LED strips will turn of automatically and orderly.

• A Stairs Sideway running LED strip control system with two motion sensors.
  
• A transformer with enough capacity to power all LED strips and controller.
  
• A certain amount meters of LED channel( LED 1903 IC controlled strips inside a particular shape of aluminum profile with a soft light PC cover)
  
• Cables with double insulated 2-wire to power LED channels ( need each power in cable for each 5 meters strips)
  
• Extended cords (double insulated 3-wire, or CAT5 cable) to connect motion sensor when needed.
  
• Extended cords (CAT5 cable prefer) to connect the beginning position of 1903 IC controlled strips and the controller.
  
• A trustable supplier for pre-sales and after-sales services.

1. Do you need aluminum profile for supporting LED strips? If yes, please refer to our 508/509 items, for ceiling mounted and recessed.
   
2. How long will be the needed strips? Take SMD5050, 60 LED chips and 20ICs per meter for example, Controller can support maximum 25 meters.
   
3. For LED strip power supply, you need to add input cables into the LED strip for each 5 meters. Otherwise the brightness and effect might get influenced.
   
4. Please noted the LED strips are with directions during installation. If you need to connect more than 5 meters, make sure the direction in the same way.
   
5. For LED power supplies, make sure that the cables are thick enough for much higher current in output side.
   
6. Make sure not to install the signal wires of sensors and strips with normal electricity cables. And use CAT5 cables for signals.
   
7. Make sure you know how to calculate the correct power of the Power supplies. You need to consider strips, controllers, cable lost, and allowance. If no, please contact with us.
   
8. LED strip flickring, and not running correctly, please check the direction of the strips, input voltage of the strips, power supply wattages, and signal interference.
   
9. For sensor sensitive problems, please try to find a best position when you install the sensors. Sensors working in this way: not sense anything, voltage of VCC and GND is 12/24VDC, and voltage of DI and GND is 0 VDC. And if it senses something, the voltage of DI and GND will change into 3.3VDC and maintain for around 3 seconds.
   

1. The installed LED strip must be with 1903IC type LED. Otherwise, the effects cannot be shown correctly.
   
2. The controller supports maximum 500 pcs of ICs, and setting stepping is 5ICs per time.
   
3. Speed can adjust from 1-99. 1: fastest, 99: slowest.
   
4. Controller MUST connect to DC12-24V. CANNOT connect to AC100-240V.
   
5. Please use CAT5 cable for the Controller Signal output, to connect with the LED strip. And maximum not exceed 10 meters.
   
6. Please use CAT5 cable for Sensor extended wires, and not more than 15 meters.
   
7. Connect downstair sensor into 01 socket, and upstair sensor into 02 socket.